MTP8102 -Semight Instruments

Features

Independent configuration
Each channel can be independently configured as NRZ or PAM4 signal system;
Multi-rate
Rate support range: 24.33-60 Gbaud;
FEC
Support FEC simulation test analysis;
Rich code types
SSPRQ/JP03A/JP03B/LIN/square wave/user-defined patterns, etc.;
Frequency dividing output
Trigger signal supports frequency division output (4-128 frequency division);
High performance
Fast rising and falling edge, low inherent jitter;
High power
Support high power mode transmitter output;
Powerful data analysis
Flexible database management functions to assist R&D in in-depth data analysis

Product Model

Category of 800G Transceiver Test Head
Product Name	PN	Type of Modules	Qty of DUT
800G Transceiver Test Head	MTP8102-DT-N	800G OSFP 800G QDD	2 2
INS： ST：Single-side temperature control was performed with TEC DT：Double-side temperature control was performed with TEC G: With Golden Light interface N: Without Golden Light interface

*Code type: SSPRQ@53.125 Gbaud, differential eye diagram @ Keysight DCA 1092C

Code Generator Indicators
	Output Type	Differential PAM4/NRZ
	Termination	Differential 100Ω, single-ended 50Ω; AC coupling
	Data patterns	PRBS 7/9/11/13/15/23/31,PRBS7~31Q SSPRQ,JP03A/03B,LIN,CJT,SW Customer Defined Pattern (64bits length)
	Data symbol rate (Gbaud)^①	24.33/24.8832/25/25.78125/26.5625/27.89/27.95/28.05 /28.125/28.2/28.9/30/48.66/49.7664/51.5625/53.125/56 /56.25/56.4/57.8/60
	Frequency accuracy (Typical)	±50 ppm
	Maximum output amplitude (differential)^②	600 mVp-p
	TR(20%–80%)^③	<10 ps
	TF(20%–80%)^③	<10 ps
	Data output RMS jitter	<350 fs

① Support more expansion rates in the future
② Net measured value of transmitting port
③ Measured with 56.25 Gbps NRZ signal

Trigger Output Indicators
	Output amplitude	>300 mVp-p
	Output type	AC coupled, single-ended
	Frequency division ratio (settable)	4/8/16/32/128
	Connector	2.92 mm female, 50 Ω
	Trigger output	Support RF switch switching A/B each 4 groups trigger switching
Error Detector Indicators
	Input type	Differential PAM4 / NRZ
	Termination	AC
	Input Impedance	100 Ω
	Receiving amplitude (differential)^①	100 ~ 600 mVp-p
	Receiving sensitivity (differential) ^②	100 mVp-p
	Data patterns	PRBS 7/9/11/13/15/16/23/31, PRBS7~31Q;
	Data symbol rate (Gbaud)	24.33/24.8832/25/25.78125/26.5625/27.89/27.95/28.05 /28.125/28.2/28.9/30/48.66/49.7664/51.5625/53.125/56 /56.25/56.4/57.8/60
	SNR Test	Support
	Clock mode	Built-in clock recovery
	Synchronization type	Auto Synchronization (level/phase)

① The measured value is the net input value at the receiving end
② When the input amplitude is <100 mVp-p, the corresponding BER may reach e-3 or even LOS

Temperature control index
	Temperature control method	Contact TEC temperature control
	Rising and falling temperature range	TEC set temperature (-10~85 ℃) Module report temperature (-5~85 ℃)
	Stability	Single channel ±1 ℃
	Control accuracy	±0.1 ℃
	Lifting and cooling efficiency	1)Depends on the use of the site temperature environment 2)Type of module to be tested Water cooler cooling power

Optical module voltage modulation (Pull-off test)
Optical module voltage modulation (Pull-off test)	Output Range (V)	3.069 ~ 3.5
General indicators
	Environment	Use in indoor environments
	Work	0℃ to +55℃, 30% to 80% relative humidity non-condensing
	Storage	-30℃ to 70℃, 10% to 90% relative humidity non-condensing
	Elevation	Working height: 0m to 2000m, storage height: 0m to 4600m
	Power	【MTP8102】: Voltage range: 100-240 VAC, Frequency range: 50/60 Hz Maximum power: 500 W, fuse specification: F10AL 250 VAC
	Warm-up time	10 min
	Dimensions (D * W * H)	132 mm × 445 mm × 684.4 mm
	Weight	Net weight ≤10.0 kg

Similar recommendation

Optical Network Test

Optical communication network plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight Instruments offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. Provide cost-effective complete solutions.

Details

Electrical Performance Test

The high-precision source meter integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, new energy, battery and other industries. Semight Instrument provides high-precision benchtop source meters and plug-in PXIe source meter modules of standard PXIe chassis, fully meeting the application of various test scenarios.

Details

Optical Chip Test

Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of COC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight Instrument provides a complete solution from bare die to COC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight Instrument's laser chip burn-in/load/unload test system has been widely recognized by the market.

Details

Power Chip Test

The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight Instrument provide integrated solutions such as wafer burn in and known good die tester, improve test efficiency and reduce test cost.

Details

Site Map