Fast Wavelength Meter
With the growing demand for communication data, it is necessary to have a larger capacity optical communication transmission system, which drives optical component/network equipment manufacturers to use coherent communication modules based on wavelength tunable lasers in their transmission backbone networks. At present, the wavelength tunable lasers and coherent modules will be used in MAN, or even access networks. Accurate measurement and wavelength calibration are crucial for tunable lasers. With the continuous increase of communication channels from the initial 40 waves to the current maximum 800, efficient and accurate wavelength testing is more critical than ever.
High wavelength accuracy±0.33ppm (typ: ±0.5pm) for wavelength calibration and metrology
Fast TestAll-solid-state structure, non-mechanical moving parts optical design, fast test speed
Support broadband modeAccurate wavelength measurement of 96Gbaud modulated optical signals
Rich trigger functionSupport external or internal trigger
Features and Benefits
High SpeedThe FWM8612 wavelength meter is in the ordinary single sampling mode, the sampling rate can be as high as 200Hz, which is 20-100 times that of the ordinary multi-wavelength based Michelson interferometer, the power accuracy is <0.5dB, and the repeatability is <0.02dB.
Internal trigger sampling modeFWM8612 has a built-in trigger signal generator, and its fast measurement function, as shown in the figure below, triggers 1000Hz to measure the switching cycle and stability of ordinary mechanical optical switches, and can observe the transient wavelength and power information of the tunable laser.
External trigger sampling modeFWM8612 fast wavelength meter supports 5V TTL trigger level and external trigger with sampling rate up to 1000Hz. It can simultaneously measure the scanning spectrum of tunable lasers, ModeMap scanning and channel calibration of tunable lasers, and synchronous monitoring of wavelength power of pulsed lasers.
Broadband working modeHigh-speed modulation will make the original narrow linewidth laser (usually kHz~MHz) spectral broadening (96Gbaud modulation signal)。
Broadband working modeFWM8612 has been further optimized on the basis of the original, and finally realized the accurate wavelength measurement of 400G QAM16 (96Gbaud) signal.
|Wavelength Index||Wavelength Range||1250~1650nm(182~240THz)|
|Wavelength Accuracy||±0.33ppm (±0.5pm@1550nm)|
|Wavelength Repeatability||±0.07ppm (±0.1pm@1550nm)|
|Wavelength Stability||<±0.3pm@24 Hour|
|Power Index||Power Accuracy||±0.5dB(±30nm from 1310 and 1550nm)|
|Multi-peak detection index||
Minimum frequency difference between main peak and secondary peak of multi-peak detection
Maximum frequency difference between main peak and secondary peak of multi-peak detection
|Measuring speed indicators||Single Sample||
|Velocity@External Trigger||External trigger 1~1000Hz|
|Velocity @ Internal Trigger||Internal trigger 1~1000Hz|
|Optical signal input indicator||Maximum Bandwidth||25GHz（200pm@1550nm）|
|Input optical signal power range||-30dBm~+10dBm（8µW~10mW）|
|Optical Interface||9/125µm single-modefiber(FC/PC)|
|Optical interface return loss||>35dB|
|Trigger Indicator||Trigger Logic level||TTL|
|External trigger||Support wavelength and power synchronization trigger（1Hz~1kHz）|
|Internal trigger||Support internal trigger frequency setting（1Hz~1kHz）|
Optical communication network plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight Instruments offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. Provide cost-effective complete solutions.
The high-precision source meter integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, new energy, battery and other industries. Semight Instrument provides high-precision benchtop source meters and plug-in PXIe source meter modules of standard PXIe chassis, fully meeting the application of various test scenarios.Details
Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of COC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight Instrument provides a complete solution from bare die to COC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight Instrument's laser chip burn-in/load/unload test system has been widely recognized by the market.Details
The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight Instrument provide integrated solutions such as wafer burn in and known good die tester, improve test efficiency and reduce test cost.Details
Email verification code
Email verification code