MBT5210-Semight Instruments

Bit Error Ratio Tester

MBT5210

4x25G Bit Error Ratio Tester

Semight Instruments MBT5210 is a high-performance bit error ratio tester with wide range data rate from 9.953~28.2 Gbps. MBT5210 provides high signal quality: Fast rising edge, low inherent jitter; Standard pseudo-random bit sequences (PRBS) can be generated functionally: 7, 9, 11, 15, 23, 31; The trigger clock supports up to half-rate clock (high speed) and other frequency division output (low speed); Built-in clock recovery; Support switching input polarity; High repeatability and traceability to standard test results. Can be fully controlled by calling external API control (LabVIEW, C #) through the USB control interface.

Datasheet

Apply for prototype

Characteristic

Multirate
9.953~28.2 Gbps and other standard rates
Parallel efficiency
Four independent channels can be tested in parallel with high efficiency
High performance
Fast rising edge, low inherent jitter
Rich code types
PRBS pattern, square wave and custom define pattern

Functions and advantages

Good signal at the transmitter
High acceptance sensitivity<40 mV

Data Output
Type of output	Differential / single-ended
Modulation format	NRZ
Data patterns PRBS	2⁷-1, 2⁹-1, 2¹⁵-1, 2²³-1, 2³¹-1, Square Wave, User Defined Pattern
Data rate	9.953~28.2 Gbps
Frequency accuracy (typ.)	±50 ppm
Output amplitude (differential)	600~800 mVp-p
Rise Time(20 – 80%)	＜16 ps
Fall time(20 – 80%)	＜16 ps
Jitter	＜515 fs
Connector	2.92 mm female，50Ω

Clock and trigger output：Support differential / single ended clock output, and the clock division ratio can be set

Output Amplitude	＞300 mV
Output Type	Differential, AC-coupled
Connector	2.92 mm female，50 Ω

Bit error detector

Input type	Differential
Input type	Single ended
Input impedance	100Ω
Input amplitude	＜1000mVpp
Sensitivity	＜40mV
Terminal	AC - AC coupling
Data code type	2⁷-1, 2⁹-1, 2¹⁵-1, 2²³-1, 2³¹-1
Data rate	9.953~28.2 Gbps
Input amplitude range (differential)	40~1000 mV
Clock mode	Built-in clock recovery
Synchronization type	Auto Synchronization (level / phase)
Connector	2.92 mm female, 50 Ω

Similar recommendation

Optical Network Test

Optical communication network plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight Instruments offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. Provide cost-effective complete solutions.

Details

Electronic Measurement

The high-precision source meter integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, new energy, battery and other industries. Semight Instrument provides high-precision benchtop source meters and plug-in PXIe source meter modules of standard PXIe chassis, fully meeting the application of various test scenarios.

Details

Optical Chip Test

Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of COC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight Instrument provides a complete solution from bare die to COC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight Instrument's laser chip burn-in/load/unload test system has been widely recognized by the market.

Details

Power Semiconductor Test

The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight Instrument provide integrated solutions such as wafer burn in and known good die tester, improve test efficiency and reduce test cost.

Details

Site Map