Site Map

Site Map

Wafer Level Burn-In

WLR3500

HV SiC Wafer burn-in System


The WLR3500 wafer burn-in system is designed to perform HTGB and HTRB burn-in of 6 wafers at one time, which can switch the aging conditions automatically , perform Vth test for each die, meet different cost requirements according to different configuration requirements and implement configurable R&D applications and mass production applications for customers, the burn-in time can range from a few minutes to tens of hours or even thousands of hours, each channel can be provided with the over-current protection independently , and result MAP data can be provided for analysis.

Feature

  • Support multiple wafer aging

    Support aging of SiC and Gan wafer products
  • High precision parameter test

    Support parameter test Idss, Igss, Vth
  • High precision leakage current test

    The highest precision leakage current resolution can reach 0.1 nA
  • Nitrogen protection

    Support nitrogen protection to prevent high voltage spark and PAD oxidation
  • Overcurrent protection

    Overcurrent protection, short-circuit current instantaneous response<100 ns
  • High temperature resistant design

    Drawer heating related to 200 ℃
  • High temperature uniformity

    Uniformity ± 3 ℃, accuracy < 1 ℃, resolution 0.1 ℃
  • Rich software functions

    Support online editing and testing Recipe / SPEC

Functions and advantages


  • Fixture, single-layer drawer and whole rack

    HV SiC Wafer burn-in System WLR3500 has three levels fixture, single-layer drawer and whole rack. Each layer can work independently.

    Fixture design The fixture is divided into two parts, Chuck and Probe card, and the wafers are combined by the Aligner equipment and put into the aging system for aging. In order to meet the number of wafer channels, the Pogo Pin life is 100,000 crimps, the temperature resistance is 175 degrees, and the positioning accuracy is ±50μm; Chuck with heating function, heating power 300W, room temperature to 175 degrees within 20 minutes, heat sink internal temperature sensor, temperature uniformity can be ±3 °C, accuracy less than 1 °C, resolution 0.1 °C. 
  • Single-layer drawer design

    Circuit of Each layer can be independently controlled, each single-layer works can be implemented in different modes, and different burn-in verification can be performed by the burn-in plan.


Parameterndex
Applicable products GaN, SiC Wafer
Applicable packaging 4inch,6inch Wafer
Aging parameters HTGB, HTRB
Test parameters Igss, Idss, Vth
System size(mm)

2100(W) X 1900(H) X 1800(D)

System power consumption <32 kW
Nitrogen protection >0.6 mPa Access
temperature range Normal temperature - 200 ℃
Voltage range Gate ± 75 V, source 2000 V
System channel 720
Number of system layers 6th floor
Current voltage overshoot No overshoot in any case
MES docking Support MES docking

Similar recommendation

Optical Network Test
Optical Network Test

Optical communication network plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight Instruments offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. Provide cost-effective complete solutions.

Details
Electrical Performance Test
Electrical Performance Test

The high-precision source meter integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, new energy, battery and other industries. Semight Instrument provides high-precision benchtop source meters and plug-in PXIe source meter modules of standard PXIe chassis, fully meeting the application of various test scenarios.

Details
Optical Chip Test
Optical Chip Test

Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of COC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight Instrument provides a complete solution from bare die to COC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight Instrument's laser chip burn-in/load/unload test system has been widely recognized by the market.

Details
Power Chip Test
Power Chip Test

The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight Instrument provide integrated solutions such as wafer burn in and known good die tester, improve test efficiency and reduce test cost.

Details
After login Download Now!

account number

password

Registered account Download Now!

full name

Please enter your name *

e-mail address

Please enter your email address *

Email verification code

Please enter your email verification code

Telephone

Please enter your contact number *

password

Please enter your login password *

Confirm Password

Please enter your login password again *
Retrieve password

e-mail address

Please enter your email number *

Email verification code

Please enter your email verification code

New Password

Please enter your login password *

Confirm Password

Please enter your login password again *