10G Burst Mode Bit Error Ratio Tester rBT1250-Semight Instruments

Features

High compatibility
Supports various PON OLT rates of 10.3125 Gbps and below
Support Combo-PON test
Dual reset signal, support Combo-PON test
SD test
Individual LOS monitoring/SD monitoring/LOS judgment for each channel
Built-in clock recovery
It can work in a real long-fiber environment, avoiding the influence of long-fiber on delay and jitter

Features and Benefits

Dual reset signal, the reset position is adjustable (Combo-pon must have 2 reset signals)
Double packet test
Each data packet has different attenuation, there are jumps between the phases of different data packets, and there are long consecutive "1" and "0" in the data packet;
Need to simulate the worst 2 ONU signal generation.
Built-in clock recovery, support long fiber test
The built-in clock recovery enables the rBT1250 to work in a real long-fiber working environment, which is basically impossible in other solutions commonly used in the industry, because those systems do not support clock recovery,It cannot adapt to the influence of long fiber on delay and jitter.

Pattern Generator Specifications
Output Type	Difference	AC/DC Coupling, 100 Ω Termination
Output Type	Single Ended	AC Coupling, 50 Ω Termination
Output Amplitude	100-600 mVp-p	Differential
Output Channel	3 independent Channels	Support Burst/Continuous mode signal generation
Pattern	PRBS7，23，31， User Defined，CID pattern
Support Data Rate	1.25/2.5/9.953/10.3125 Gbps
Rise Time	<40 ps	20%~80%
Jitter	<12 ps	Peak to peak Jitter
Pre-emphasis	Support pre-weighting adjustment to improve the impact of test cable test fixture on signal quality
Pattern Sequence	Each channel supports independent preamble/dead load/protection time pattern sequence setting
CID Pattern	Support add continuous “1”，continuous “0” pattern as length from 64-88 bits(adjustable)
Connector	SMA

文档下载

名称

版本

发布时间

下载

rBT1250 X-PON突发信号误码测试仪-使用说明书

V7.0

2022-07-20

点击下载

Similar recommendation

Optical Network Test

Optical communication network plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight Instruments offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. Provide cost-effective complete solutions.

Details

Electrical Performance Test

The high-precision source meter integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, new energy, battery and other industries. Semight Instrument provides high-precision benchtop source meters and plug-in PXIe source meter modules of standard PXIe chassis, fully meeting the application of various test scenarios.

Details

Optical Chip Test

Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of COC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight Instrument provides a complete solution from bare die to COC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight Instrument's laser chip burn-in/load/unload test system has been widely recognized by the market.

Details

Power Chip Test

The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight Instrument provide integrated solutions such as wafer burn in and known good die tester, improve test efficiency and reduce test cost.

Details

Site Map