30/50GHz Sampling Scope DCA6201-Semight Instruments

Features

Efficient measurement
Support simultaneous measurement of all channels and parallel measurement
Multiple measurement functions
Meet the normal NRZ and PAM4 eye diagram test parameters;
Automatic test
The remote command control mode is convenient and fast
Ensure accurate performance
High performance ensures test consistency

Features and Benefits

Integrated multi-port design
Small size(about 1/4 of the traditional sampling oscilloscope), saves space;
4 optical ports optional, which can test 4 optical eye diagrams at the same time;
4 differential electrical ports optional, 30G BW, support AOC and other module electrical port parameter tests;
Calibrated reference receiver
Comply with the industry frequency response tolerance, compared with the traditional industry standard sampling oscilloscope, the eye diagram shape consistency is very high;
As shown in the figure, the NRZ eye diagram
Calibrated reference receiver
Comply with the industry frequency response tolerance, compared with the traditional industry standard sampling oscilloscope, the eye diagram shape consistency is very high;
As shown in the figure is the PAM4 eye diagram

Optical Specification		DCA6201-B30	DCA6201-B50
	Optical channel bandwidth	30 GHz	50 GHz（option IRC）
	Fiber input	62.5/125 µm FC/UPC (single-mode/multi-mode)
	Wavelength range	850 ~ 1650 nm
	Calibrated Wavelengths (OE conversion gains)	850/1310/1550 nm
	Filters	25.78 Gbps (25/50/100 Gb Ethernet) 26.56 Gbps (400 Gb Ethernet) 27.95 Gbps (OTU4) 28.05 Gbps (32× Fiber Channel) 26.5625Gbaud PAM4 28.9Gbaud PAM4	53.125GBaud PAM4 53.125GBaud NRZ 49.7664G NRZ (50G PON) 24.8832G NRZ (50G PON) 12.4416G NRZ (50GPON)
	Average power monitor accuracy y	± 5 %(after calibration)
	ADC resolution	14 Bit
	Optical sensitivity	-8 dBm
	Measurement consistency	Average Power：±0.1 dB Extinction Ratio：±0.3 dB Mask Margin：± 5 %(after calibration) TDECQ(PAM4 signal)：±0.5dB
	Max Input（None-Destruction, Peak）	Max. 5 mW (+7 dBm)
	Max Input（Linearity）	Max.1.25 mW (+1 dBm)
	Monitor Average Power Range	-20 dBm to +1dBm
	Average power monitor accuracy	Single-mode ±5% ±200 nW ±connector uncertainty
		Multimode (characteristic) ± 10% ± 200 nW ± connector uncertainty
		Due to variations in mode-filling conditions, the measured power in multimode fiber will vary more than the measured power in single-mode fiber. For users needing the most accurate power measurements, use an optical power meter for multimode power measurements
	Input return loss	＞23 dB
Electrical Specifications	Electrical channel bandwidth	33 GHz
	Input signal type	AC-coupled
	Input connector	2.92 mm female
	Dynamic range of input	500 mVp-p
	DC accuracy	3mV
	RMS noise	1.5mV (Typical)
	ADC resolution	14 Bit
	Max Input Amplitude	±1 V
	Impedance	50 Ω
Mainframe Specifications	Sampling system	Acquisition Mode：Sampling (Default)，Envelop and Average 2048 points/Waveform，Accumulation Waveform Numbers：15 waveforms to unlimited
	Sensitivity	200 mV
	Maximum trigger Input	＜±1.5 V
	Trigger Impedance	50 Ω
	Connector type	2.92 mm female
	Frequency Range	500 M~15 GHz
	Integrated temperature monitor	Support
	Remote control	Ethernet Socket (TCP Command)
	Test standards	Ethernet、SDH/SONET、OTN、InfiniBand、Fiber Channel

文档下载

名称

版本

发布时间

下载

DCA6201 TCP远程控制使用说明

V1.2

2022-07-20

点击下载
DCA上位机简要使用说明

V0.7

2022-07-20

点击下载

Similar recommendation

Optical Network Test

Optical communication network plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight Instruments offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. Provide cost-effective complete solutions.

Details

Electrical Performance Test

The high-precision source meter integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, new energy, battery and other industries. Semight Instrument provides high-precision benchtop source meters and plug-in PXIe source meter modules of standard PXIe chassis, fully meeting the application of various test scenarios.

Details

Optical Chip Test

Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of COC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight Instrument provides a complete solution from bare die to COC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight Instrument's laser chip burn-in/load/unload test system has been widely recognized by the market.

Details

Power Chip Test

The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight Instrument provide integrated solutions such as wafer burn in and known good die tester, improve test efficiency and reduce test cost.

Details

Site Map