Laser Diode Burn-In
BI6203
CoC Burn-in System
The BI6203 burn-in system is a high-density, multi-functional testing system specifically designed for the verification of the burn-in lifespan of semiconductor laser chips. The system adopts a modular design with large single-layer structure. Integrating multi-channel power supplies, temperature controllers, real-time data acquisition capabilities. Standardized drawers and flexible fixture are suitable for various sizes of CoC (Chip on Carrier). The fixtures can be easily replaced to accommodate different device types. Drawers could be replaced when new test functions are added, such as thermistor monitoring and power monitoring.
Driving Power Supply
Supports up to 4224 channels of 4-quadrant driving power supply
Strong Thermal Conductivity
Temperature deviation ＜ ±1.0℃ for the overall thermal sink（40～100℃）
Temperature Control
Each fixture has independent heating, temperature control, monitoring, over temperature protection and heat dissipation units for energy saving
Fixture
Fishbone-type fixture which support wire bonding on it
Safety and Reliability
Comprehensive protection mechanisms through hardware and software eliminate potential issues such as EOS
Online Power Monitoring
Optional configuration for online power monitoring, supporting complete LIV or EA scans, with the ability to analyze Ith. The test repeatability deviation ＜±1%
4224 CoC Simultaneously Burn-in
Production capacity flexibly configured based on customer requirements
Software Functions
All test results, test statuses, and abnormal conditions are recorded in the database which could be stored and traced efficientlyFunctions and Advantages
Special Temperature Control Structure with Excellent Thermal Conductivity
CoC, CoS drawer and clamp
|
No. |
Module |
Part number |
Description |
|
1 |
CoC Burn-in System cabinet (including computer) |
P09000037 |
Main frame, computer, software（remark: up to 11 layers） |
|
2 |
CoC Burn-in System single layer (including Driving board) |
P02004448 |
- 96 channels standard driving board - Switch mode power supply - Temperature control module - Back panel - CDA N2 control system |
|
3 |
Burn-in drawer |
P02004255 |
- Double fixtures with 96 channel PD - Drawer temperature range 40～120℃ - G4 long fixture, fixture bottom plate thickness 2mm & 1mm - Heat sink temperature uniformity ±2℃ |
|
FB020313 |
- Drawer temperature range 40～120℃ - G4 long fixture, fixture bottom plate thickness 1mm - Heat sink temperature uniformity ±2℃ |
||
|
4 |
Burn-in fixture（including up and bottom fixtures） |
C04000223 |
- Supports 48 channel DML CoC |
|
5 |
Load board |
|
5Ω resistor board |
Similar recommendation
High speed communication test plays an important role in the rapid development of big data, cloud computing, 5G communication and other markets.
Semight offers various of instruments for optical Transceiver/Component testing, including wide bandwidth sampling oscilloscope, NRZ/PAM4 bit error ratio tester , burst error ratio tester, fast wavelength meter, optical spectrum analyzer, high precise source measure unit, 400G network analyzer ,optical power meter, optical attenuator, optical switch etc. We provide cost-effective, complete solutions for optical testing.
The high-precision source measure units integrates the functions of voltage source, current source, voltmeter, ampere meter, and electronic load in one, which is widely used in high-precision IV test and measurement for various discrete components, photovoltaic, green energy, battery and other industries. Semight provides high-precision benchtop SMU and plug-in PXIe SMU of standard PXIe chassis, fully meeting the application of various test scenarios.
Details
Burn-in testing of laser is an important method to ensure the reliability of laser. Through the test of CoC or bare die, the early failure of laser caused by the defects in the process of laser production can be screened out in advance. Semight provides a complete solution from bare die to CoC, from high temperature(150℃ or higher) to low temperature (-40℃), with CoC automatic loading and unloading system, forming a complete test solution, Semight's laser chip burn-in/load/unload test system has been widely recognized by the market.
Details
The semiconductor front-end test is mainly used in the wafer processing to check whether the processing parameters of the wafer products meet the design requirements or there are defects affecting the yield after each step of the manufacturing process. The semiconductor back-end test equipment is mainly used after wafer processing to check whether the performance of the chip meets the requirements, which belongs to the electrical performance test. Semight provides solutions such as Wafer Level Burn In system and Known Good Die handler for SiC testing, offering the value to customer in test efficiency improvement and test cost reduction.
DetailsFollow
Name
E-mail verfication code
Phone
Password
Confirm Password
E-mail address
E-mail verification code
New Password
Confirm Password
Datasheet
Ask for demo
